Diagnóstico: Códigos de Error (modelos 2000 en adelante)

CROWLEY

Master Therion
para modelos 2004 en adelante

1 -Pon el interruptor de arranque en la posición "OFF" y el interruptor Run/Stop en "Run".

2 - Mantén apretado el botón de reajuste del odómetro.

3 - Gira el interruptor de arranque a la posición "Ignition" y suelta el botón de reajuste del odómetro. Se encenderá la iluminación de fondo, la aguja del velocímetro deberá recorrer su gama completa y las lámparas indicadoras se deben iluminar. La palabra “diag” debe entonces aparecer.

4 - Aprieta el botón del reajuste del odómetro una vez y verás el menú "PSSPt" con la primera selección "P" destellando.

5 - Cada letra representa un área del módulo del diagnóstico. El módulo que está destellando es el que vas a comprobar. Para moverse a partir de una letra (módulo) al siguiente, aprieta el botón del reajuste del odómetro una vez. (de P a S a SP a t y de nuevo a P etc.)
P = ECM/ICM (módulo de control electrónico [EFI]/módulo de control de ignición [Carburador])
S = TSM/TSSM (intermitencias/Alarma)
SP = velocímetro
T = tacómetro

6 - Para seleccionar un área del diagnóstico, apretar y sostener el botón del reajuste del odómetro hacia adentro durante 5 segundos y soltar. Si hay algún aviso de fallo será exhibido el código, si no aparecerá la palabra "none". Pulsar de nuevo el botón para ver si existen códigos adicionales.

7 - Anotar los códigos.

8 - presionar y soltar el botón del reajuste del odómetro. El número de módulo será exhibido.

NOTA: Para determinar si un código es actual o histórico, borre el código exhibido manteniendo apretado el botón del reajuste del odómetro (más de 5 segundos) hasta que aparezca la palabra "clear". Soltar el botón del reajuste del odómetro. Girar a la posición "OFF"e l interruptor de arranque. Arrancar la moto y apagarla, entonces volver a inspeccionar los códigos de error repitiendo los pasos 1 a 9. Si el código es actual reaparecerá.

9 - Presionar y soltar el botón del reajuste del odómetro para continuar con el módulo siguiente.

10 - Para finalizar, girar el interruptor de arranque a la posición "OFF".


-----------------------------------------------------------------------------------------------------------------------------------------
no traduzco todos los códigos (mucho curro), si alguien necesita traducir algo que no entiende que lo diga.
-----------------------------------------------------------------------------------------------------------------------------------------


DTC FAULT CONDITION MODULE

"BUS Er" Serial data bus shorted/low/open/high
B0563 Battery Voltage High TSM/TSSM
B1004 Fuel Level Sending Unit Low Instruments
B1005 Fuel Level Sending Unit High/Open Instruments
B1006 Accessory Line Overvoltage Instruments
B1007 Ignition Line Overvoltage Instruments
B1008 Reset Switch Closed Instruments
B1122 Right turn output fault
B1131 Alarm Output Low TSM/TSSM
B1132 Alarm Output High TSM/TSSM
B1134 Starter Output High TSM/TSSM
B1135 Accelerometer Fault TSM/TSSM
B1141 Ignition switch open/low
B1151 Sidecar BAS Low TSM/TSSM
B1152 Sidecar BAS High TSM/TSSM
B1153 Sidecar BAS Out of Range TSM/TSSM
P0106 MAP Sensor Rate of Range Error Carb
P0107 Map Sensor Failed Open/Low Carb
P0107 Map Sensor Open/Low EFI
P0108 Map Sensor Failed High Carb
P0108 Map Sensor High EFI
P0112 IAT Sensor Voltage Low EFI
P0113 IAT Sensor Voltage Open/High EFI
P0117 ET Sensor Voltage Low EFI
P0118 ET Sensor Voltage Open/High EFI
P0122 TP Sensor Open/Low EFI
P0123 TP Sensor High EFI
P0131 Front 02 sensor low (lean)
P0132 Engine running rich
P0134 Front 02 sensor open/not responding
P0151 Rear 02 sensor low (lean)
P0152 Rear 02 sensor high (rich)
P0154 Rear 02 sensor open/not responding
P0261 Front Injector Open/Low EFI
P0262 Front Injector High EFI
P0263 Rear Injector Open/Low EFI
P0264 Rear Injector High EFI
P0373 CKP Sensor Intermittent Carb
P0373 CKP Sensor Intermittent EFI
P0374 CKP Sensor Not Detected Carb
P0374 CKP Sensor Synch Error EFI
P0501 VSS Low Carb
P0501 VSS Low EFI
P0502 VSS High/Open Carb
P0502 VSS High/Open EFI
P0505 Loss of Idle Sped Control EFI
P0562 Battery Voltage Low Carb
P0562 Battery Voltage Low EFI
P0563 Battery Voltage High Carb
P0563 Battery Voltage High EFI
P0602 Calibration Memory Error Carb
P0603 EEPROM Failure Carb
P0603 ECM EEPROM Error EFI
P0604 RAM Failure Carb
P0605 Program Memory Error Carb
P0605 ECM Flash Error EFI
P0607 Converter Error Carb
P0661 Intake solenoid low/open
P0662 Intake solenoid high/shorted
P1001 System Relay Coil Open/Low EFI
P1002 System relay Coil High/Shorted EFI
P1003 System relay Contacts Open EFI
P1004 System Relay Contacts Closed EFI
P1009 Incorrect Password Carb
P1009 Incorrect Password EFI
P1010 Missing Password Carb
P1010 Missing Password EFI
P1351 Front Ignition Open/Low Carb
P1351 Front Ignition Open/Low EFI
P1352 Front Ignition Coil High/Shorted Carb
P1352 Front Ignition Coil High/Shorted EFI
P1353 Front Cylinder No Combustion EFI
P1354 Rear Ignition Coil Open/Low Carb
P1354 Rear Ignition Coil Open/Low EFI
P1355 Rear Ignition Coil High/Shorted Carb
P1355 Rear Ignition Coil High/Shorted EFI
P1356 Rear Cylinder No Combustion EFI
P1357 Intermittent Secondary Front EFI
P1358 Intermittent Secondary Rear EFI
U1016 Loss of ICM/ECM Serial Data Instruments
U1016 Loss of ECM Serial Data, Vehicle Speed, Vehicle Inhibit Motion or Powertrain Security Status TSM/TSSM
U1064 Loss of TSM/TSSM Serial Data Carb
U1064 Loss of TSM/TSSM Serial Data EFI
U1064 Loss of TSM/TSSM Serial Data Instruments
U1097 Loss of Speedometer Serial data Carb
U1097 Loss of Speedometer Serial data EFI
U1097 Loss of Speedometer Serial data TSM/TSSM
U1255 Missing Message at Speedometer EFI
U1255 Serial Data Error/Missing Message EFI
U1255 Serial Data Error/Missing Message Instruments
U1255 Serial Data Error/Missing Message TSM/TSSM
U1300 Serial Data Low Carb
U1300 Serial Data Low EFI
U1300 Serial Data Low Instruments
U1300 Serial Data Low TSM/TSSM
U1301 Serial Data Open/High Carb
U1301 Serial Data Open/High EFI
U1301 Serial Data Open/High Instruments
U1301 Serial Data Open/High TSM/TSSM


2006 models with 02 sensors (Dynas)

P0131 Front 02 sensor lean for any length of time
P0151 Rear 02 sensor lean for any length of time
Above codes can also be set if 02 sensor fails.


-----------------------

AFR – Air Fuel Ratio

ATS – Air Temperature Sensor

BAS – Bank Angle Sensor

CCM – Cruise Control Module

CKP – Crank Position Sensor. The CKP generates an “AC signal” which is sent to the ECM where it is used to reference engine position (TDC) and speed. Home position established by taking readings off the 22 teeth on the alternator rotor.

DTC – Diagnostic Trouble Codes

ECM – Electronic Control Module. (The Computer) Computes the spark advance for proper ignition timing and fuel control based on sensor inputs (from CKP, MAP & TP sensors) and controls the low-voltage circuits for the ignition coils and injectors. The dwell time for the ignition coil is also calculated in the microprocessor and is dependent upon battery voltage. The programmed dwell feature gives adequate spark at all speeds.

ECT – Engine Coolant Temperature. Sensor also controls the cooling fan relay that provides 12 Vdc to the fans.

EFI – Electronic Fuel Injection

EFP – Electronic Fuel Pump

ET – Engine Temperature sensor

FI – Fuel Injectors

FPR – Fuel Pressure regulator

IAC – Idle Air Control actuator

IAT – Intake Air Temperature sensor

ISS – Ion Sensing System…detonation detection

MAP – manifold Absolute Pressure sensor. The MAP sensor monitors the intake manifold pressure (vacuum) and sends the information to the ECM. The EMC then adjusts the spark and fuel-timing advance curves for optimum performance.

TP – Throttle Position Sensor

TSM/TSSM (Turn Signal/ Turn Signal Security Module)

VE – Volume Efficiency

VSS – Vehicle Speed Sensor. Used as an input for idle speed control
 
Respuesta: Diagnóstico: Códigos De Error (modelos 2004 En Ad

Crowley, esto no tiene palabras. Por fin sabremos que le pasa a nuestra burra sin tener que pasar por taller.
 
Respuesta: Diagnóstico: Códigos De Error (modelos 2004 En Ad

Muy interesante, ya me lo he imprimido, pero me pregunto si estos datos vienen en los papeles de la moto?.
 
Respuesta: Diagnóstico: Códigos de Error (modelos 2004 en ad

También se puede ver en modelos anteriores al 2004, pero es una movida; hay que cortocircuitar unos terminales en el peine de conexión de diagnóstico y tras una operación similar, contar las veces que destella una luz y segun los destellos es un código....
Si queréis lo pongo, pero personalmente yo no me atrevo a hacerlo en mi moto. :shock:
 
Diagnóstico: Códigos De Error (modelos 2004 En Adelante)

nunca te acuestes sin saber algo nuevo, con crowley :wink:

que bueno el post compa sin duda viene bien, en cuenta tenga un rato lo pruebo espero no cargarmela jeje
 
Respuesta: Diagnóstico: Códigos De Error (modelos 2004 En Ad

Falconazo, estoy de acuerdo contigo. Crowley, eres un autentico hacha, ¿ como te las apañas para hacer lo que haces?
 
Respuesta: Diagnóstico: Códigos de Error (modelos 2004 en ad

Desde el 95 navegando y buscando en la red algo tengo que haber aprendido , no? :lol: :wink:
 
Respuesta: Diagnóstico: Códigos De Error (modelos 2004 En Ad

Holas, en vista de lo leído no he podido aguantar, le he dado al boton del cuenta y luego contacto y me ha salido lo del menú en mi sportster del 2003. y sale: d01Clr, d02Clr, d03Clr ... así sucesivamente hasta el número 10, después sale PPU y finaliza con una cifra de cinco dígitos (48677). Alguien me podría indicar para que sirven esas funciones?, he estado buscando por internet y no sé ver nada que me ayude. Mas que nada es para saber si puedo beneficiarme. Gracias
 
Modelos 00-03

[video=youtube;NBDDV1qUd6g]http://www.youtube.com/watch?feature=endscreen&v=NBDDV1qUd6g&NR=1[/video]

Nuevo video:

[video=youtube;dHb3r-HfYE4]http://www.youtube.com/watch?v=dHb3r-HfYE4&feature=youtu.be[/video]

MODELOS 00-03


1 Current 53 ECM flash error
2 Historic 53 ECM flash error
3 Current 54 ECM EEPROM error
4 Historic 54 ECM EEPROM error
5 Current 63 ECM serial data low
6 Current 63 ECM serial data open/high
7 Current 63 TSSM serial data low
8 Current 63 TSSM serial data open/high
9 Current 61 Loss of TSM/TSSM serial data
10 Current 14 Loss of all ECM serial data (state of health)
10 24 Loss of vehicle speed
10 33 Loss of vehicle inhibit motion
10 43 Loss of power train security status
11 Current 33 System relay contacts open
12 Current 33 System relay coil high/shorted
13 Current 33 System relay coil open/low
14 Current 33 System relay contacts closed
15 Current 99 Incorrect password
16 Current 99 Missing password
17 Current 41 CKP sensor intermittent
18 Current 41 CKP sensor synch error
19 Current 11 TP sensor open/low
20 Current 11 TP sensor high
21 Current 12 MAP sensor open/low
22 Current 12 MAP sensor high
23 Current 14 ET sensor voltage low
24 Current 14 ET sensor open/high
25 Current 15 IAT sensor voltage low
26 Current 15 IAT sensor open/high
27 Current 24 Front ignition coil open/low
28 Current 25 Rear ignition coil open/low
29 Current 24 Front ignition coil high/shorted
30 Current 25 Rear ignition coil high/shorted
31 Current 24 Front cylinder combustion intermittent
32 Current 25 Rear cylinder combustion intermittent
33 Current 23 Front injector open/low
34 Current 32 Rear injector open/low
35 Current 23 Front inject or high
36 Current 32 Rear injector high
37 Current 16 Battery volt age low
38 Current 16 Battery volt age high
39 Current 43 VSS sensor low
40 Current 43 VSS sensor high
41 Current N/A (no speedo code for this) Check engine light open/low NO CHECK ENGINE LAMP AT KEY ON or CHECK ENGINE LAMP ON CONTINUOUSLY
42 Current N/A (no speedo code for this) Check engine light high NO CHECK ENGINE LAMP AT KEY ON
43 Current 35 Tachometer low
44 Current 35 Tachometer h igh
45 Current 25 Rear cylinder no combustion
46 Current 24 Front cylinder no combustion
47 Current 34 Loss of idle speed control IDLE AIR CONTROL
48 Current 35 Accelerometer fault
49 Current 34 Starter output high
50 Current 25 Ignition enable output high
51 Current 21 Left turn output fault
52 Current 22 Right turn output fault
53 Current 11 Battery voltage high
54 Current 31 Alarm output low
55 Current 32 Alarm output high
56 Current 41 Ignition switch open/low
57 Current 42 Cam position sensor
57 Historic 63 ECM serial data low
58 Historic 63 ECM serial da ta open/high
59 Historic 63 TSSM serial data low
60 Historic 63 TSSM serial data open/high
61 Historic 61 Loss of TSM/TSSM serial data
62 Historic 14 Loss of all ECM serial data (state of health)
63 Historic 33 System relay contacts open
64 Historic 33 System relay coil high/shorted
65 Historic 33 System relay coil open/low
66 Historic 33 System relay contacts closed
67 Historic 99 Incorrect password
68 Historic 99 Missing password
69 Historic 41 CKP sensor intermittent
70 Historic 41 CKP sensor synch error
71 Historic 11 TP sensor ope n/low
72 Historic 11 TP sensor high
73 Historic 12 MAP sensor open/low
74 Historic 12 MAP sensor high
75 Historic 14 ET sensor voltage low
76 Historic 14 ET sensor open/high
77 Historic 15 IAT sensor voltage low
78 Historic 15 IAT sensor open/high
79 Historic 24 Front ignition coil open/low
80 Historic 25 Rear ignition coil open/low
81 Historic 24 Front ignition coil high/shorted
82 Historic 25 Rear ignition coil high/shorted
83 Historic 24 Front cylinder combustion intermittent
84 Historic 25 Rear cylinder combustion intermittent
85 Historic 23 Front injector open/low
86 Historic 32 Rear injector open/low
87 Historic 23 Front injector high
88 Historic 32 Rear injector high
89 Historic 16 Battery voltage low
90 Historic 16 Battery voltage high
91 Historic 43 VSS sensor lo w
92 Historic 43 VSS sensor high
93 Historic N/A Check engine light open/low NO CHECK ENGINE LAMP AT KEY ON or CHECK ENGINE LAMP ON CONTINUOUSLY
94 Historic N/A Check engine light high NO CHECK ENGINE LAMP AT KEY ON
95 Historic 35 Tachometer low
96 Historic 35 Tachometer high
97 Historic 25 Rear cylinder no combustion
98 Historic 24 Front cylinder no combustion
99 Historic 34 Loss of idle speed control
100 Historic 35 Accelerometer fault
101 Historic 34 Starter output high
102 Historic 25 Ignition enable output high
103 Historic 21 Left turn output fault
104 Historic 22 Right turn output fault
105 Historic 11 Battery voltage high
106 Historic 31 Alarm output low
107 Historic 32 Alarm output high
108 Historic 41 Ignition switc h open/low
 
Re: Respuesta: Diagnóstico: Códigos De Error (modelos 2004 E

[quote user="CROWLEY" post="22598"]Desde el 95 navegando y buscando en la red algo tengo que haber aprendido , no? :lol: :wink:[/quote]

Joder :shock: :shock: :shock: :shock: :shock:
 
Respuesta: Diagnóstico: Códigos De Error (modelos 2000 En Ad

Uf, complicado para mi, de todos modos "copio y guardo" por si debo recurrir algún día .
Gracias por la información
 
A esto en mi pueblo se le llama ser un ARTISTA, si señor con dos co....., por eso servidor, sigue con los carburadores con un destornillador y pa lante,
Te has merecido una cervecitas
 
:shock: Un día de estos me voy a poner a estudiar ingles porque cada vez me entero menos. Si ya me lo decía mi padre. :sad:
 
Lista ampliada para modelos '08-'09

Lista ampliada para modelos '08-'09

El sistema para verlos es el mismo que en las '04-up


B0563 Battery Voltage High TSM/TSSM
B1004 Fuel Level Sending Unit Low Instruments
B1005 Fuel Level Sending Unit High/Open Instruments
B1006 Accessory Line Overvoltage Instruments
B1007 Ignition Line Overvoltage Instruments
B1008 Reset Switch Closed Instruments
B1121 (TSM) Left Turn Output Fault - (HFSM) Left Turn Output Open
B1122 (TSM) Right Turn Output Fault - (HFSM) Right Turn Output Open
B1123 (HFSM) Left Turn Output Short to Ground
B1124 (HFSM) Right Turn Output Short to Ground
B1125 (HFSM) Left Turn Output Short to Battery
B1126 (HFSM) Right Turn Output Short to Battery
B1131 (HFSM) Alarm Output Low
B1131 Alarm Output Low TSM/TSSM
B1132 (HFSM) Alarm Output High
B1132 Alarm Output High TSM/TSSM
B1134 Starter Output High TSM/TSSM
B1135 Accelerometer Fault TSM/TSSM
B1136 (HFSM) Accelerometer Tip Test Error
B1141 (TSM) Ignition Switch Low/Open - (HFSM) Ignition Switch Low/Open
B1142 Smart Security System Internal Fault
B1143 (HFSM) Security Antenna Short to Ground
B1144 (HFSM) Security Antenna Short to Battery
B1145 (HFSM) Security Antenna Open
B1151 Bank Angle Sensor(BAS) Short to Ground
B1151 Sidecar BAS Low TSM/TSSM
B1152 Bank Angle Sensor(BAS) Short to Battery
B1152 Sidecar BAS High TSM/TSSM
B1153 Bank Angle Sensor(BAS) High
B1153 Sidecar BAS Out of Range TSM/TSSM
B1154 Clutch Switch Input Short to Ground
B1155 Neutral Switch Input Short to Battery
P0106 MAP Sensor Rate of Range Error Carb
P0107 Map Sensor Failed Open/Low Carb
P0107 Map Sensor Open/Low EFI
P0108 Map Sensor Failed High Carb
P0108 Map Sensor High
P0112 IAT Voltage Low
P0113 IAT Sensor Voltage Open/High EFI
P0113 IAT Voltage Open/High
P0117 ET Sensor Low
P0118 ET Sensor High
P0118 ET Sensor Voltage Open/High EFI
P0120 TPS1 Range Error
P0122 TP Sensor Open/Low EFI
P0122 TPS1 Low
P0123 TP Sensor High EFI
P0123 TPS2 High/Open
P0131 Front Oxygen Sensor Low
P0132 Front Oxygen Sensor High
P0134 Front Oxygen Sensor Inactive
P0151 Rear Oxygen Sensor Low
P0152 Rear Oxygen Sensor High
P0154 Rear Oxygen Sensor Inactive
P0220 TPS2 Range Error
P0222 TPS2 Low
P0223 TPS2 High/Open
P0261 Front Injector Open/Low
P0262 Front Injector High EFI
P0263 Rear Injector Open/Low EFI
P0264 Rear Injector High EFI
P0371 Crank Position Sensor (CKP)
P0372 Crank Position Sensor (CKP)
P0373 CKP Sensor Intermittent
P0374 CKP Sensor Not Detected Carb
P0374 CKP Sensor Synch Error EFI
P0444 Purge Solenoid Open/Low
P0445 Purge Solenoid High
P0501 VSS Sensor Low
P0502 VSS High/Open
P0505 Loss of Idle Sped Control EFI
P0562 Battery Voltage Low
P0563 Battery Voltage High
P0572 Brake Switch Low
P0577 Cruise Control Input High
P0602 Calibration Memory Error Carb
P0603 ECM EEPROM Memory Error
P0603 EEPROM Failure Carb
P0604 RAM Failure Carb
P0605 ECM Flash Error EFI
P0605 ECM FLASH Memory Error
P0605 Program Memory Error Carb
P0607 Converter Error Carb
P06415 V+Vref 1 Out Of Range
P06515 V+Vref 2 Out Of Range
P1001 System Relay Coil Open/Low
P1002 System Relay Coil High/Shorted
P1003 System relay contacts open
P1004 System Relay Contacts Closed
P1009 Incorrect Password
P1010 Missing Password
P1270 TGS Validation Error
P1351 Front Ignition Coil Driver Open/Low
P1352 Front Ignition Coil Driver High/Shorted
P1353 Front Cylinder No Combustion
P1354 Rear Ignition Coil Driver Open/Low
P1355 Rear Ignition Coil Driver High/Shorted
P1356 Rear Cylinder No Combustion
P1357 Front Cylinder Combustion Intermittent
P1358 Rear Cylinder Combustion Intermittent
P1475 Exhaust Actuation Position Error
P1477 Exhaust Actuator Open/Low
P1478 Exhaust Actuator Shorted/High
P1501 Jiffy Stand Sensor Low
P1502 Jiffy Stand Sensor High
P1510 EFI Limited Performance Mode
P1511 EFI Power Management Mode
P1512 EFI Forced Idle Mode
P1514 Air Flow Fault
P1600 EFI Module Processor Internal Error
P2100 EFI Motor Circuit Open
P2101 EFI Motor Circuit Range Performance (Actuation Error)
P2102 EFI Motor Circuit Low
P2103 EFI Motor Circuit High
P2105 EFI Forced engine shutdown
P2107 EFI Module Processor Internal Fault
P2119 EFI Motor Throttle Body Range Performance
P2122 TGS1 Low/Open
P2123 TGS1 High
P2127 TGS2 Low/Open
P2128 TGS2 High
P2135 TPS Correlation Error
P2138 TGS Correlation Error (Twist grip sensor)
P2176 EFI Closed Position Not Learned
U1016 Loss of ECM Vehicle Speed, Vehicle Inhibit Motion or Powertrain Security Status TSM/TSSM
U1016 Loss of ICM/ECM Serial Data Instruments
U1064 Loss of TSM/FSFM Serial Data to ICM / ECM
U1064 Loss of TSM/TSSM Serial Data Instruments
U1097 Loss of Speedometer Serial data Carb
U1097 Loss of Speedometer Serial data EFI
U1097 Loss of Speedometer Serial Data to ECM
U1097 Loss of Speedometer Serial data TSM/TSSM
U1255 Missing Message at Speedometer EFI
U1255 Serial Data Error
U1255 Serial Data Error/Missing Message EFI
U1255 Serial Data Error/Missing Message Instruments
U1255 Serial Data Error/Missing Message TSM/TSSM
U1300 ECM Serial Data Low
U1300 Serial Data Low
U1300 Serial Data Low Instruments
U1300 Serial Data Low TSM/TSSM
U1301 Serial Data Open/High Carb
U1301 Serial Data Open/High EFI
U1301 Serial Data Open/High Instruments
U1301 Serial Data Open/High TSM/TSSM
 
Mi pregunta es si se pueden ajustar parámetros como el CO de cada cilindro a partir de los mandos como se puede hacer por ejemplo con una FZ1
 
Wow, eres un crack :mrblue:
Gracias a esto hemos podido confirmar que le pasaba a la Sporter de una amiga sin pasar por el taller.

Gracias :love:
 
Saludos de nuevo!!

He mirado los codigos de error de mi iron y me aparece P0505 "Loss of Idle Sped Control EFI"

Alguien me puede decir que significa??

Muchas gracias a todos y felices fiestas!!!
 
[quote user="DARKRIDER" post="107593"]Saludos de nuevo!!

He mirado los codigos de error de mi iron y me aparece P0505 "Loss of Idle Sped Control EFI"

Alguien me puede decir que significa??

Muchas gracias a todos y felices fiestas!!![/quote]

The speedometer signal is an extremely important input for the Delphi fuel
injection system. The ECM monitors throttle position and speed signal inputs in
order to properly maintain the set idle speed. If the ECM loses the speed signal
for any reason while the throttle is closed, the ECM assumes the vehicle is
stopped and will adjust the idle air control counts to bring engine rpm to the set
idle speed. This could set a P0505 code and adversely affect engine idle.
 
Según el manual de diagnosis :

P0505 - Loss of idle speed control :
Loss of idle speed control will result if the idle RPM is +-200 from present idle speed and IAC motor is at zero or maximum for greater than 5 seconds.
- Loss of idle speed control doesn't necessarily mean that the IAC is bad. There are other causes such as intake leaks, misfiring cylinder.
- Leaking injectors can cause poor idle. To check for leaky injectors remove A/C. Then with throttle wide open, turn key to ON for 2 seconds and then off for 2 seconds five consecutive times. Replace injectors if there is any evidence of raw fuel in the bores.
- Vacuum leaks - check for leaks
- Contaminated fuel
- Excessive Oil in crankcase
- TP sensor reading greater than 1 % (cable misadjusted), battery less then 9 Volts, or vehicle speed sensor (VSS) greater than 0 will disable idle speed control.
- Loss of battery power to terminal 31 of ECM.

Osea :

Tienes una perdida de control en la velocidad del relantí, que se ha incrementado o disminuido en algun momento en 200 rpm más de lo establecido, puede ser por una de esas múltiples causas descritas
 
Atrás
Arriba